PRELIMINARY TECHNICAL DATA
ThreePhaseEnergyMeteringIC
withPulseOutput
ADE7752
a
Preliminary Technical Data
*
FEATURES
GENERALDESCRIPTION
High Accuracy, Supports 50 Hz/60 Hz IEC 687/1036
Less than 0.1% Error Over a Dynamic Range of
500 to 1
Compatible with 3-phase/3-wire and 3-phase/4-wire
configurations
The ADE7752 is a high accuracy three phase electrical
energy measurement IC. The part specifications surpass the
accuracy requirements as quoted in the IEC1036 standard.
The only analog circuitry used in the ADE7752 is in the
ADCs and reference circuit. All other signal processing (e.g.,
multiplication, filtering and summation) is carried out in the
digital domain. This approach provides superior stability and
accuracy over extremes in environmental conditions and over
time.
The ADE7752 supplies average real power information on
the low frequency outputs F1 and F2. These logic outputs
may be used to directly drive an electromechanical counter or
interface with an MCU. The CF logic output gives instan-
taneous real power information. This output is intended to be
used for calibration purposes, or as interface with an MCU.
The ADE7752 includes a power supply monitoring circuit
on the AVDD supply pin. The ADE7752 will remain inactive
until the supply voltage on VDD reaches 4 V. If the supply falls
below 4 V, the ADE7752 will also be reset and no pulses will
be issued on F1, F2 and CF.
The ADE7752 Supplies Average Real Power on the
Frequency Outputs F1 and F2
The High Frequency Output CF Is Intended for
Calibration and Supplies Instantaneous Real Power
The Logic Output REVP indicates a Potential Miswiring or
Negative Power for each phase
Direct Drive for Electromechanical Counters and
Two Phase Stepper Motors (F1 and F2)
Proprietary ADCs and DSP Provide High Accuracy over
Large Variations in Environmental Conditions and
Time
On-Chip Power Supply Monitoring
On-Chip Creep Protection (No Load Threshold)
On-Chip Reference 2.5 V 8% (30 ppm/8C Typical)
with External Overdrive Capability
Single 5 V Supply, Low Power (15 mW Typical)
Low Cost CMOS Process
Internal phase matching circuitry ensures that the voltage and
current channels are phase matched. An internal no-load
threshold ensures that the ADE7752 does not exhibit any
creep when there is no load.
The ADE7752 is available in 24-lead SOIC packages.
FUNCTIONAL BLOCK DIAGRAM
VDD
RESET
17
3
5
IAP
IAN
Power
Supply
Monitor
ADC
6
HPF
LPF
16
VAP
Φ
PHASE
CORRECTION
ADC
ADE7752
7
IBP
IBN
ADC
ADC
Σ
8
HPF
LPF
LPF
15
VBP
2
Φ
PHASE
CORRECTION
DGND
CLKIN
CLKOUT
19
20
ICP
ICN
VCP
VN
ADC
ADC
10
14
HPF
Φ
PHASE
CORRECTION
13
DIGITAL-TO-FREQUENCY
CONVERTER
4kΩ
2.5V
REF
11
12
4
18
21
22
23
24
1
REFIN/OUT
REVP SCF S0 S1 F2 F1 CF
*Patentspending
AGND
REV. PrB 08/01
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 1999