Low Distortion, 3.2 GHz, RF DGA
Data Sheet
ADA4961
FEATURES
FUNCTIONAL BLOCK DIAGRAM
High speed
−3 dB bandwidth: 3.2 GHz
24
23
22
21
20
19
−1 dB bandwidth: 1.8 GHz
Slew rate: 12,000 V/μs
EXPOSED
PAD
ADA4961
Digitally adjustable gain
Voltage gain: −6 dB to +15 dB
Power gain: −3 dB to +18 dB
5-bit parallel or SPI bus gain control with fast attack
IMD3/HD3 distortion, maximum gain, 5 V, high performance
(HP) mode
2
3
17
16
VOUT+
VIN+
0dB TO 21dB
ATTEN
+15dB
VIN–
VOUT–
DNC
18
15
14
4
5
GND
GND
DNC
DNC
1
7
8
9
10
11
12
13
6
IMD3/HD3 at 1 GHz: −90 dBc/−83 dBc
IMD3/HD3 at 1.5 GHz: −85 dBc/−75 dBc
IMD3/HD3 at 2 GHz: −70 dBc/−70 dBc
Low noise
NOTES
1. DNC = DO NOT CONNECT. DO NOT CONNECT TO THIS PIN.
Noise density referred to output (RTO): −154 dBm/Hz
Noise figure: 5.5 dB at AV = 15 dB, 1 GHz
Differential impedances: 100 Ω input, 50 Ω output
Low power mode operation, power-down control
Single 3.3 V or 5 V supply operation
Available in 24-lead, 4 mm × 4 mm LFCSP
Figure 1.
APPLICATIONS
ADC driver for 10-bit to 14-bit GSPS converters
RF/IF gain blocks
Line drivers
Instrumentation
Satellite communications
Data acquisition
Military systems
GENERAL DESCRIPTION
The ADA4961 is a high performance, BiCMOS RF digital gain
amplifier (DGA), optimized for driving heavy loads out to
2.0 GHz and beyond. The device typically achieves −90 dBc
IMD3 performance at 500 MHz and −85 dBc at 1.5 GHz. This
RF performance allows GHz converters to achieve their optimum
performance with minimal limitations of the driver amplifier or
constraints on overall power that typically result from GaAs
amplifiers. This device can easily drive 10-bit to16-bit HS
converters.
digital adjustability provides for 1 dB resolution, thus optimizing
the signal-to-noise ratio (SNR) for input levels spanning 21 dB.
The ADA4961 is optimized for wideband, low distortion
performance at frequencies up to 2 GHz. These attributes,
together with wide gain adjustment and relatively low power,
make the ADA4961 the amplifier of choice for many high speed
applications, including IF, RF, and broadband applications
where dynamic range at very high frequencies is critical.
The ADA4961 is ideally suited for driving not only analog-to-
digital converters (ADCs), but also mixers, pin diode attenuators,
SAW filters, and multielement discrete devices. It is available in
a 4 mm × 4 mm, 24-lead LFCSP and operates over a
temperature range of −40°C to +85°C.
For many receiver applications, antialias filter (AAF) designs
can be simplified or not required.
The ADA4961 has an internal differential input impedance of
100 Ω and a differential dynamic output impedance of 50 Ω,
eliminating the need for external termination resistors. The
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2014–2019 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
5秒后页面跳转
全球首块英伟达H200交付 黄仁勋“送货上门”
常用8脚开关电源芯片型号大全
74HC04芯片引脚图及功能、应用电路图讲解
CR6842芯片参数、引脚配置、应用电路图详解
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
