High Speed
Dual Pin Electronic
a
AD53522
FEATURES
FUNCTIONAL BLOCK DIAGRAM (One-Half)
1000 MHz Toggle Rate
Driver/Comparator/Active Load and Dynamic Clamp
Included
Inhibit Mode Function
100-Lead LQFP Package with Built-In Heat Sink
Driver
48 ꢃ Output Resistance
800 ps Tr/Tf for a 3 V Step
Comparator
V
V
V
V
V
V
EE
CC
CC
CC
EE
EE
VH
VTERM
DATA
DATAB
IOD
AD53522
VCH
VHDCPL
OUT
DRIVER
IODB
RLD
VLDCPL
VCL
1.1 ns Propagation Delay at 3 V
Load
RLDB
VL
ꢄ40 mA Voltage Programmable Current Range
50 ns Settling Time to 15 mV
PWRD
HCOMP
VCCO
QH
APPLICATIONS
Automatic Test Equipment
Semiconductor Test Systems
Board Test Systems
QHB
COMPARATOR
Instrumentation and Characterization Equipment
QL
QLB
LCOMP
PRODUCT DESCRIPTION
The AD53522 is a complete, high speed, single-chip solution
that performs the pin electronics functions of driver, comparator,
and active load (DCL) for ATE applications. In addition, the
driver contains a dynamic clamp function and the active load
contains an integrated Schottky diode bridge.
VCOM
IOLC
+1
VCOM_S
V/I
IOXRTN
ACTIVE LOAD
The driver is a proprietary design that features three active states:
Data High mode, Data Low mode, and Term mode, as well as
an Inhibit State. In conjunction with the integrated dynamic
clamp, this facilitates the implementation of a high speed active
termination. The output voltage range is –0.5 V to +6.5 V to
accommodate a wide variety of test devices.
PROT_LO
PROT_HI
INHL
INHLB
THERM*
IOHC
V/I
1.0ꢀA/ꢁK
DR_GND GND_ROT PWRGND HQGND THERMSTART
The dual comparator, with an input range equal to the driver
output range, features PECL compatible outputs. Signal tracking
capability is in the range of 3 V/ns.
ꢂ9
*ONLY 1 (ONE) THERM PER DEVICE
The active load can be set for up to 40 mA load current. IOH, IOL
and the buffered VCOM are independently adjustable. On-board
Schottky diodes provide high speed switching and low capacitance.
,
that is proportional to absolute temperature. The gain is trimmed
to a nominal value of 1.0 µA/K. As an example, the output current
can be sensed by using a 10 kΩ resistor connected from 10 V to
the THERM (IOUT) pin. A voltage drop across the resistor will
be developed that equals 10 kΩ ϫ 1 µA/°K = 10 mV/°K = 2.98 V
at room temperature.
Also included is an on-board temperature sensor that gives an
indication of the silicon surface temperature of the DCL. This
information can be used to measure JC and JA or flag an alarm
if proper cooling is lost. Output from the sensor is a current sink
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
www.analog.com
© 2003 Analog Devices, Inc. All rights reserved.