8-Bit Dual Nonvolatile Memory
Digital Potentiometer
a
AD5232*
FEATURES
FUNCTIO NAL BLO CK D IAGRAM
Nonvolatile Memory Preset Maintains Wiper Settings
Dual Channel, 256-Position Resolution
Full Monotonic Operation DNL < 1 LSB
10 kꢀ, 50 kꢀ, 100 kꢀ Terminal Resistance
Linear or Log Taper Settings
Push-Button Increment/Decrement Compatible
SPI-Compatible Serial Data Input with Readback
Function
AD5232
CS
V
DD
RDAC1
REGISTER
ADDR
DECODE
RDAC1
CLK
SDI
A1
W1
B1
SDI
SERIAL
INTERFACE
GND
EEMEM1
3 V to 5 V Single Supply or ꢁ2.5 V Dual Supply
Operation
14 Bytes of User EEMEM Nonvolatile Memory for
Constant Storage
Permanent Memory Write Protection
100-Year Typical Data Retention TA = 55ꢂC
RDAC2
RDAC2
REGISTER
SDO
SDO
A2
W2
B2
WP
EEMEM
CONTROL
RDY
EEMEM2
14 BYTES
USER EEMEM
PR
V
SS
APPLICATIONS
T he basic mode of adjustment is the increment and decrement
command controlling the present setting of the Wiper position
setting (RDAC) register. An internal scratch pad RDAC register
can be moved UP or DOWN one step of the nominal terminal
resistance between terminals A and B. T his linearly changes the
wiper to B terminal resistance (RWB) by one position segment of
the devices’ end-to-end resistance (RAB). For exponential/loga-
rithmic changes in wiper setting, a left/right shift command
adjusts levels in ±6 dB steps, which can be useful for audio and
light alarm applications.
Mechanical Potentiometer Replacement
Instrumentation: Gain, Offset Adjustment
Programmable Voltage-to-Current Conversion
Programmable Filters, Delays, Time Constants
Line Impedance Matching
Power Supply Adjustment
DIP Switch Setting
GENERAL D ESCRIP TIO N
T he AD5232 device provides a nonvolatile, dual-channel,
digitally controlled variable resistor (VR) with 256-position
resolution. T hese devices perform the same electronic adjust-
ment function as a potentiometer or variable resistor. T he
AD5232’s versatile programming via a microcontroller allows
multiple modes of operation and adjustment.
T he AD5232 is available in a thin T SSOP-16 package. All parts
are guaranteed to operate over the extended industrial tempera-
ture range of –40°C to +85°C. An evaluation board is available,
Part Number: AD5232EVAL.
In the direct program mode a predetermined setting of the RDAC
register can be loaded directly from the microcontroller.
Another key mode of operation allows the RDAC register to be
refreshed with the setting previously stored in the EEMEM
register. When changes are made to the RDAC register to estab-
lish a new wiper position, the value of the setting can be saved
into the EEMEM by executing an EEMEM save operation.
Once the settings are saved in the EEMEM register these values
will be automatically transferred to the RDAC register to set the
wiper position at system power ON. Such operation is enabled
by the internal preset strobe and the preset can also be accessed
externally.
100
75
50
25
R
R
WA
WB
All internal register contents can be read out of the serial data
output (SDO). T his includes the RDAC1 and RDAC2 registers,
the corresponding nonvolatile EEMEM1 and EEMEM2 regis-
ters, and the 14 spare USER EEMEM registers available for
constant storage.
0
0
64
128
192
256
CODE – Decimal
Figure 1. Symmetrical RDAC Operation
*P atent pending.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
www.analog.com
© Analog Devices, Inc., 2001