256-Position Two-Time Programmable
I2C Digital Potentiometer
AD5170
FUNCTIONAL BLOCK DIAGRAM
FEATURES
256-position
A
W
B
TTP (two-time programmable) set-and-forget resistance
setting allows second-chance permanent programming
Unlimited adjustments prior to OTP (one-time
programming) activation
FUSE
LINKS
OTP overwrite allows dynamic adjustments with user
defined preset
V
DD
1
2
End-to-end resistance: 2.5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ
Compact MSOP-10 (3 mm × 4.9 mm) package
Fast settling time: tS = 5 µs typ in power-up
Full read/write of wiper register
RDAC
REGISTER
GND
AD0
AD1
ADDRESS
DECODE
8
Power-on preset to midscale
Extra package address decode pins AD0 and AD1
Single-supply 2.7 V to 5.5 V
SDA
SCL
SERIAL INPUT
REGISTER
Low temperature coefficient: 35 ppm/°C
Low power, IDD = 6 µA maximum
Figure 1.
Wide operating temperature: –40°C to +125°C
Evaluation board and software are available
Software replaces µC in factory programming applications
APPLICATIONS
Systems calibration
The AD5170 is programmed using a 2-wire, I2C® compatible
digital interface. Unlimited adjustments are allowed before
permanently (there are actually two opportunities) setting the
resistance value. During OTP activation, a permanent blow fuse
command freezes the wiper position (analogous to placing
epoxy on a mechanical trimmer).
Electronics level setting
Mechanical Trimmers® replacement in new designs
Permanent factory PCB setting
Transducer adjustment of pressure, temperature, position,
chemical, and optical sensors
RF amplifier biasing
Automotive electronics adjustment
Gain control and offset adjustment
Unlike traditional OTP digital potentiometers, the AD5170 has
a unique temporary OTP overwrite feature that allows for new
adjustments even after the fuse has been blown. However, the
OTP setting is restored during subsequent power-up
conditions. This feature allows users to treat these digital
potentiometers as volatile potentiometers with a programmable
preset.
GENERAL OVERVIEW
The AD5170 is a 256-position, two-time programmable (TTP)
digital potentiometer1 that employs fuse link technology to
enable two opportunities at permanently programming the
resistance setting. OTP is a cost-effective alternative to EEMEM
for users who do not need to program the digital potentiometer
setting in memory more than once. This device performs the
same electronic adjustment function as mechanical
potentiometers or variable resistors with enhanced resolution,
solid-state reliability, and superior low temperature coefficient
performance.
For applications that program the AD5170 at the factory,
Analog Devices offers device programming software running
on Windows NT®, 2000, and XP® operating systems. This
software effectively replaces any external I2C controllers, thus
enhancing the time-to-market of the user’s systems.
1 The terms digital potentiometer, VR, and RDAC are used interchangeably.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
