PRODUCT DATASHEET
AAT3601178
Total Power Solution for Portable Applications
General Description
Features
•
•
The AAT3601 is a member of AnalogicTech’s Total Power
Management ICTM (TPMICTM) product family. It contains a
single-cell Lithium Ion/Polymer battery charger, a fully
integrated step-down converter and 5 low dropout (LDO)
regulators. The device also includes 2 load switches for
dynamic power path/sleep mode operation, making it
ideal for small portable short-range communications
enabled mobile devices and telephones.
Voltage Regulator VIN Range: 4.5V to 6V
Complete Power Integration
Integrated Load Switches to Power Converters from
AC Adapter or Battery Automatically
Low Standby Current
▪
•
•
200μA (typ) w/LDO1, LDO2 and LDO5 Active,
No Load
▪
One Step-Down Buck Converter (NP)
1.24V, 300mA Output
1.5MHz Switching Frequency
▪
The battery charger is a complete thermally regulated
constant current/constant voltage linear charger. It
includes an integrated pass device, reverse blocking pro-
tection, high accuracy current and voltage regulation,
charge status, and charge termination. The charging
current and the charge termination current as well as
recharge voltage are programmable with either an exter-
nal resistor and/or by a standard I2C interface.
▪
Fast Turn-On Time (120μs typ)
▪
Five LDOs Programmable by I2C
•
LDO1: 3.4V, 150mA (PE)
LDO2: 3.4V, 300mA (NP)
LDO3: 1.24V, 300mA (PE)
LDO4: 1.85V, 300mA (NP)
LDO5: 1.85V, 300mA (PE)
PSRR: 60dB @10kHz
Noise: 50μVrms
▪
▪
▪
▪
▪
The step-down DC/DC converter is integrated with inter-
nal compensation and operates at a switching frequency
of 1.5MHz, thus minimizing the size of external compo-
nents while keeping switching losses low and efficiency
greater than 95%. All LDO output voltages are program-
mable using the I2C interface.
▪
▪
•
•
One Battery Charger
Digitized Thermal Regulation
Charge Current Programming up to 1.4A
Charge Current Termination Programming
Automatic Trickle Charge for Battery Preconditioning
▪
▪
▪
▪
The five LDOs offer 60dB power supply rejection ratio
(PSRR) and low noise operation making them suitable for
powering noise-sensitive loads. The LDOs and DC/DC
converter are separated into Permanent-Enabled (PE)
and Non-Permanent (NP) enabled supplies.
(2.8V Cutoff)
Watchdog (WDI) Timer Input
Two Reset (RSTIN, RSTLPW) Timer Outputs
▪
•
•
•
•
•
Separate Enable Pins for PE and NP Supplies
Digital Programming of Major Parameters via I2C
Over-Current Protection
Over-Temperature Protection
5x5mm TQFN55-36 Package
All six voltage regulators operate with low quiescent cur-
rent. The total no load current when the 3 PE LDOs are
enabled is only 200μA.
The device includes a watchdog timer input and two
reset outputs for the watchdog and LDO regulation. The
device also can be programmed through a standard I2C
interface.
Applications
•
•
•
•
•
•
Digital Cameras
GSM or CDMA Cellular Phones
Handheld Instruments
PDAs and Handheld Computers
Portable Media Players
Short-Range Communication Headsets
The AAT3601 is available in a thermally enhanced low
profile 5x5x0.8mm 36-pin TQFN package.
w w w . a n a l o g i c t e c h . c o m
3601.2008.07.1.1
1