PROPRIETARY INFORMATION PRODUCT DATASHEET
AAT1271A
TM
SwitchReg
1.5A Step-Up Current Regulator for Flash LEDs
General Description
Features
•
•
•
The AAT1271A is a high-efficiency, high-current boost
converter capable of 1.5A typical output current. It is an
ideal power solution for LED photo flash applications in
all single cell Li-ion powered products.
VIN Range: 2.7V to 5.5V
Dual Channel Output
Up to 1.5A Regulated Output Current (750mA per
channel)
•
•
•
•
•
•
•
Up to 85% Efficiency with Small Inductor (1μH)
2 MHz Switching Frequency
Separate Flash Enable
The AAT1271A maintains output current regulation by
switching the internal high-side and low-side switch
transistors. The transistor switches are pulse-width
modulated at a fixed frequency of 2MHz. The high
switching frequency allows the use of a small inductor
and output capacitor, making the AAT1271A ideally
suited for small battery-powered applications.
Separate Flash Inhibit
User-Programmable Safety Timer
Single Resistor Sets Flash and Movie Mode Current
AS2Cwire Single Wire Programming:
Movie Mode Current
Flash/Movie Mode Current Ratio
Movie Mode Output Configuration
Flash Safety Timer
▪
AnalogicTech’s proprietary AS2Cwire™ (Advanced Simple
Serial Control™) serial digital interface is used to enable,
disable, configure, and program the operation of the
AAT1271A. Using the AS2Cwire interface, the movie-
mode current level for each LED, the safety timer delay,
and the flash-to-movie-mode current ratio can be pro-
grammed to one of 16 levels. In addition, the single-wire
serial protocol sets output channel control. The AAT1271A
also includes a separate Flash Enable input to initiate
both the flash operation and the default timer which can
be used either to terminate a flash event at the end of a
user-programmed delay or as a safety feature. Also
included is a Flash Inhibit pin which reduces the flash
current to movie-mode levels during high battery
demand.
▪
▪
▪
•
•
•
True Load Disconnect
Input Current Limit
Over-Voltage (Open LED, Open Circuit), Short Circuit,
and Over-Temperature Protection
Shutdown Current < 1.0μA
14-pin TDFN 3x3 mm Package
-40°C to +85°C Temperature Range
•
•
•
Applications
•
•
•
•
•
Camcorder Video Light (Torch Light)
Cellphones/Smartphones
Digital Still Cameras (DSCs)
LED Photo Flash/Torch
The maximum flash and movie-mode current is set by
one external resistor where the ratio of Flash to Movie-
mode current is set at approximately 7.3:1. One or two
LEDs can be connected to the AAT1271A, where in the
case of two LEDs the output current is matched between
each diode.
Mobile Handsets
The AAT1271A contains a thermal management system
to protect the device in the event of an output short-
circuit condition. Built-in circuitry prevents excessive
inrush current during start-up. The shutdown feature
reduces quiescent current to less than 1.0μA.
The AAT1271A is available in a Pb-free, thermally-
enhanced 14-pin 3x3mm TDFN package.
w w w . a n a l o g i c t e c h . c o m
1271A.2008.07.1.0
1
5秒后页面跳转
全球首块英伟达H200交付 黄仁勋“送货上门”
常用8脚开关电源芯片型号大全
74HC04芯片引脚图及功能、应用电路图讲解
CR6842芯片参数、引脚配置、应用电路图详解
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
