A200RI/A300RISeries
High Isolation, 2W & 3W
Single & Dual Output
DC/DC Convverteerrss
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min.
Typ.
5.0
12.0
24.0
48.0
Max.
5.25
13.2
26.4
52.8
Units
Key Features:
5 VDC Input 4.75
● 2W & 3W Output Power
● Compact DIP Case
● 3,000 VDC Isolation
● Tight Line/Load Regulation
● Single & Dual Outputs
● 17 Standard Models
● 800 kH MTBF
12 VDC Input 10.8
24 VDC Input 21.6
48 VDC Input 43.2
π (Pi) Filter
Input Voltage Range
VDC
Input Filter
Reverse Polarity Input Current
Short Circuit Input Power
Output
0.5
2,500
A
mW
Parameter
Conditions
Min.
Typ.
2.0
1.0
0.2
0.2
40
Max.
4.0
3.0
0.3
0.5
50
Units
%
%
%
%
mV P - P
mV P - P
mV rms
%
μSec
%
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
● Industry Standard Pin-Out
Dual Output , Balanced Loads
Vin = Min to Max
Load Regulation
Iout = 10% to 100%
Ripple & Noise (20 MHz) (Note 1)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Transient Recovery Time (Note 2)
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
General
Over Line, Load & Temp.
50% Load Step Change
75
5
120
50
6.0
0.02
0.01
%/ºC
Continuous
Min.
60 Seconds 3,000
500 VDC 1,000
100 kHz, 1V
40
Parameter
Isolation Voltage
Conditions
Typ.
Max.
Units
VDC
MΩ
pF
kHz
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
Operating Temperature Range
50
80
100
Conditions
Min.
-25
Typ.
Max.
+71
Units
ºC
-25
-40
+90
+125
ºC
ºC
Storage Temperature Range
Cooling
Free Air Convection
MicroPower Direct
232 Tosca Drive
Humidity
Physical
Case Size
Case Material
Weight
Reliability Specifications
Parameter
RH, Non-condensing
95
%
Stoughton, MA 02072
USA
1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.42 Oz (12g)
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min.
800
Typ.
Typ.
Max.
Units
kHours
MTBF
Absolute Maximum Ratings
Parameter
Conditions
Min.
Max.
7.5
15.0
30.0
55.0
260
Units
5 VDC Input -0.7
12 VDC Input -0.7
24 VDC Input -0.7
48 VDC Input -0.7
Input Voltage Surge (1 Sec)
VDC
Lead Temperature
Internal Power Dissipation
1.5 mm From Case For 10 Sec.
All Models
ºC
mW
3,000
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.