Series
A200RHI
Very High Isolation, 2W
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Key Features:
Conditions
Min.
4.5
Typ.
5.0
Max.
5.5
Units
• 2W Output Power
• 8,000 VDC Isolation
• 2 µA Leakage Current Max
• Compact DIP Case
• Single & Dual Outputs
• Meets EN55022 Class A
• 600 kH MTBF
5 VDC Input
Input Voltage Range
12 VDC Input 10.8
24 VDC Input 21.6
12.0
24.0
13.2
26.4
VDC
Input Filter
π (Pi) Filter (Complies with EN55022 Class A)
Reverse Polarity Input Current
Short Circuit Input Power
Output
0.5
A
2,000
mW
Parameter
Conditions
Min.
Typ.
2.0
2.0
0.3
0.5
30
Max.
4.0
4.0
0.5
1.0
50
Units
%
%
%
%
mV P - P
mV P - P
mV rms
%
µSec
%
• Industry Standard Pin-Out
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Dual Output , Balanced Loads
Vin = Min to Max
Load Regulation
Iout = 10% to 100%
Ripple & Noise (20 MHz) (Note 1)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Transient Recovery Time (Note 2)
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
General
Over Line, Load & Temp.
50% Load Step Change
100
5
120
50
6.0
0.02
RoHS Compliant
0.01
%/ºC
Continuous
Parameter
Conditions
Min.
5,600
60 Seconds 6,000
Typ.
Max.
Units
VDC
VDC
VDC
µA
Isolation Voltage, Rated
Isolation Test Voltage
Isolation Test Voltage
Leakage Current
Flash Tested For 1 Second 8,000
240 VAC, 60 Hz
2
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
500 VDC
100 kHz, 1V
10
GΩ
pF
kHz
20
30
80
25
Parameter
Conditions
Min.
-25
-25
Typ.
Max.
+60
+90
Units
ºC
ºC
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
-40
+125
ºC
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Free Air Convection
RH, Non-condensing
Humidity
95
%
Physical
Case Size
1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.42 Oz (12g)
Case Material
Weight
Reliability Specifications
Parameter
MTBF
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Conditions
Min.
600
Typ.
Typ.
Max.
Units
kHours
MIL HDBK 217F, 25ºC, Gnd Benign
Absolute Maximum Ratings
Parameter
Conditions
Min.
Max.
7.5
15.0
30.0
260
Units
5 VDC Input -0.7
12 VDC Input -0.7
24 VDC Input -0.7
Input Voltage Surge (1 Sec)
VDC
Lead Temperature
Internal Power Dissipation
1.5 mm From Case For 10 Sec
All Models
ºC
2,000
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.