A1100RW Series
Miniature, 10W DIP
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Key Features:
• 10W Output Power
Conditions
12 VDC Input
Min.
7.0
Typ.
8.0
Max.
9.0
Units
• Compact DIP Case
Input Start Voltage
24 VDC Input 14.0
48 VDC Input 30.0
π (Pi) Filter (Complies with EN55022 Class “A”)
16.0
33.0
18.0
36.0
VDC
• 2:1 Input Voltage Range
• Single & Dual Outputs
• 1,500 VDC Isolation
• Meets EN55022 Class “A”
• 1.0 MH MTBF
Input Filter
Reverse Polarity Input Current
Short Circuit Input Power
Output
0.5
2,500
A
mW
Parameter
Conditions
Min.
Typ.
0.6
0.5
0.3
0.7
0.5
50
Max.
1.2
1.0
1.0
1.5
1.2
85
100
15
180
500
5.0
0.02
Units
%
%
%
%
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
• Industry Standard Pin-Out
Dual Output , Balanced Loads
Vin = Min to Max
Load Regulation, 2.5 Vout Models
Load Regulation, All Other Models
Ripple & Noise (20 MHz) (Note 1)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Transient Recovery Time (Note 2)
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
General
Iout = 10% to 100%
Iout = 10% to 100%
%
mV P - P
mV P - P
mV rms
%
µSec
%
Over Line, Load & Temp.
110
150
250
3.0
25% Load Step Change
0.01
%/ºC
Continuous (Autorecovery)
Parameter
Isolation Voltage
Conditions
Min.
Typ.
Max.
Units
VDC
VDC
MΩ
pF
60 Seconds 1,500
Isolation Voltage Test
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Flash Tested for 1 Second 1,650
500 VDC 1,000
100 kHz, 1V
1,000 1,200
400
RoHS Compliant
kHz
Parameter
Conditions
Min.
-40
-40
Typ.
+25
Max.
+60
+90
Units
ºC
ºC
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Conducted EMI
Ambient
Case
-40
+125
ºC
Free Air Convection
RH, Non-condensing
EN55022 Class “A”
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
95
%
Physical
Case Size
1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm)
Metal with Non-Conductive Base
0.61 Oz (17.3g)
Case Material
Weight
Reliability Specifications
Parameter
MTBF
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Conditions
Min.
1.0
Typ.
Typ.
Max.
Units
MHours
MIL HDBK 217F, 25ºC, Gnd Benign
Absolute Maximum Ratings
Parameter
Conditions
Min.
Max.
25.0
50.0
100.0
260
Units
VDC
12 VDC Input -0.7
24 VDC Input -0.7
48 VDC Input -0.7
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
1.5 mm From Case For 10 Sec
All Models
ºC
2,500
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.