Series
A100HI
Ultra-High Isolation, 1.5W
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Key Features:
Conditions
Min. Typ. Max.
Units
• 1.5W Output Power
• 8,000 VDC Isolation
• 2 µA Leakage Current Max
• Compact DIP Case
• Single & Dual Outputs
• Meets EN55022 Class A
• 1.0 MH MTBF
5 VDC Input
4.5
5.0
5.5
Input Voltage Range
12 VDC Input 10.8
15 VDC Input 13.5
(Pi) Filter
12.0
15.0
13.2
16.5
VDC
Input Filter
Reverse Polarity Input Current
Short Circuit Input Power
Output
0.5
A
1,000
mW
Parameter
Conditions
Min. Typ. Max.
Units
%
%
• Industry Standard Pin-Out
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
2.0
0.5
1.2
4.0
2.0
1.5
Dual Output , Balanced Loads
For Vin Change of 1%
%
Load Regulation, (Note 1)
Ripple & Noise (20 MHz) (Note 2)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Temperature Coefficient
Output Short Circuit
General
See Model Selection Guide
30
40
50
15
mV P - P
mV P - P
mV rms
%
Over Line, Load & Temp.
120
Continuous
0.01
0.02
%/ºC
Parameter
Conditions
Min. Typ. Max.
Units
VDC
VDC
µA
Isolation Voltage, Rated
Isolation Test Voltage
Leakage Current
60 Seconds 8,000
Flash Tested For 1 Second 8,800
240 VAC, 60 Hz
2
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
500 VDC
100 kHz, 1V
10
G
pF
kHz
10
15
100
50
Parameter
Conditions
Min. Typ. Max.
Units
ºC
ºC
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Ambient
Case
-40
-40
-55
+85
+95
+125
ºC
Free Air Convection
RH, Non-condensing
Humidity
95
%
Physical
Case Size
Case Material
Weight
1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.42 Oz (12g)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min. Typ. Max.
2.0
Units
MHours
Absolute Maximum Ratings
Parameter
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Conditions
Min. Typ. Max.
Units
5 VDC Input -0.7
12 VDC Input -0.7
15 VDC Input -0.7
1.5 mm From Case For 10 Sec
All Models
7.0
17.0
21.0
260
Input Voltage Surge (1 Sec)
VDC
Lead Temperature
Internal Power Dissipation
ºC
mW
1,000
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com