Document 459
For National Semiconductor
Flyback Transformers LM5070 PoE Interface – 3 Watt
• Flyback transformers for 3 W PoE applications
• Designed to operate in continuous mode at 250 kHz with
an input of 36 – 72 Vdc
• 1500 Vrms isolation from primary and bias to secondary
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos
bronze. Other terminations available at additional cost.
Weight 2.05 g
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 350 per 13″ reel Plastic tape: 32 mm wide, 0.42 mm
thick, 20 mm pocket spacing, 9.16 mm pocket depth
PCB washing Only pure water or alcohol recommended
Inductance Inductance
Leakage
DCR max (Ohms)4
Turnsratio6
pri :sec pri :bias (A)
Part
at 0 A2
at Ipk3
inductance5
max (µH)
Ipk3
number1 ±10% (µH)
min (µH)
pri
bias
sec
Output7
0.3 3.3 V, 0.91 A
0.3 5.0 V, 0.6 A
0.3 12 V, 0.25 A
C1590-AL_
C1591-AL_
C1592-AL_
310
310
310
279
279
279
1.02
1.02
1.04
2.01
2.01
2.01
0.066
0.118
0.700
4.75
4.50
4.25
1 : 0.19
1 : 0.28
1 : 0.70
1 : 0.70
1 : 0.70
1 : 0.70
1. When ordering, please specify packaging code:
2. Inductance is for the primary, measured at 10 kHz, 0.1 Vrms, 0 Adc.
3. Ipk is peak primary current drawn at minimum input voltage.
4. DCR for the secondary is per winding.
5. Leakage inductance measured between pins 3 and 4 with all other pins
shorted.
C1592-ALD
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic
tape (350 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To
have a leader and trailer added ($25 charge), use
code letter D instead.
6. Turns ratio is with the secondary windings connected in parallel.
7. Output of the secondary is with the windings connected in parallel. Bias
winding output is 12 V, 20 mA.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Dot above pin1
0.355
9,02
max
0.004/0,10
0.041
1,05
6
5
0.520
13,21
3
max
Recommended
Land Pattern
Pri
Sec
0.339
8,60
0.050
1,27
0.028
0,70
7
8
4
2
0.080
2,03
0.370
9,40
8
1
4
Bias
1
0.430
10,92
max
0.098
2,50
0.098
2,50
Secondary windings to be connected
in parallel on the PC board
1
5
Specifications subject to change without notice.
Please check our website for latest information.
Document459 Revised10/29/08
© Coilcraft, Inc. 2009