1200 MHz to 2500 MHz Balanced Mixer,
LO Buffer and RF Balun
ADL5365
FEATURES
FUNCTIONAL BLOCK DIAGRAM
VCMI
20
IFOP
19
IFON
18
PWDN
17
COMM
16
RF frequency range of 1200 MHz to 2500 MHz
IF frequency range of dc to 450 MHz
Power conversion loss: 7.3 dB
SSB noise figure of 8.3 dB
SSB noise figure with 5 dBm blocker of 18.5 dB
Input IP3 of 36 dBm
ADL5365
1
2
3
4
5
15
14
13
12
11
VPMX
RFIN
LOI2
VPSW
VGS1
VGS0
LOI1
Typical LO drive of 0 dBm
Single-ended, 50 Ω RF and LO input ports
High isolation SPDT LO input switch
Single-supply operation: 3.3 V to 5 V
Exposed paddle 5 mm × 5 mm, 20-lead LFCSP
1500 V HBM/500 V FICDM ESD performance
RFCT
COMM
COMM
BIAS
GENERATOR
APPLICATIONS
Cellular base station receivers
Transmit observation receivers
Radio link downconverters
6
7
LGM3
8
9
10
VLO3
VLO2
LOSW
NC
NC = NO CONNECT
Figure 1.
GENERAL DESCRIPTION
The ADL5365 provides two switched LO paths that can be
used in TDD applications where it is desirable to rapidly switch
between two local oscillators. LO current can be externally set
using a resistor to minimize dc current commensurate with the
desired level of performance. For low voltage applications, the
ADL5365 is capable of operation at voltages down to 3.3 V with
substantially reduced current. Under low voltage operation, an
additional logic pin is provided to power down (<200 μA) the
circuit when desired.
The ADL5365 uses a highly linear, doubly balanced passive
mixer core along with integrated RF and LO balancing circuitry
to allow for single-ended operation. The ADL5365 incorporates
an RF balun, allowing for optimal performance over a 1200 MHz
to 2500 MHz RF input frequency range using high-side LO
injection for RF frequencies from 1700 MHz to 2500 MHz and
low-side injection for frequencies from 1200 MHz to 1700 MHz.
The balanced passive mixer arrangement provides good LO-to-
RF leakage, typically better than −30 dBm, and excellent inter-
modulation performance. The balanced mixer core also provides
extremely high input linearity, allowing the device to be used in
demanding cellular applications where in-band blocking signals
may otherwise result in the degradation of dynamic performance.
The ADL5365 is fabricated using a BiCMOS high performance
IC process. The device is available in a 5 mm × 5 mm, 20-lead
LFCSP and operates over a −40°C to +85°C temperature range.
An evaluation board is also available.
Table 1. Passive Mixers
RF Frequency
(MHz)
Single
Mixer
Single Mixer +
IF Amp
Dual Mixer +
IF Amp
500 to 1700
ADL5367 ADL5357
ADL5365 ADL5355
ADL5358
ADL5356
1200 to 2500
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2009 Analog Devices, Inc. All rights reserved.