Triple Differential Driver
With Output Pull-Down
AD8133
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Triple high speed fully differential driver
225 MHz −3 dB large signal bandwidth
24
23
22
21
20
19
Easily drives 1.4 V p-p video signal into source-terminated
100 Ω UTP cable
1600 V/µs slew rate
OPD
1
2
3
4
5
18
17
V
V
C
OCM
S+
AD8133
V
S–
Fixed internal gain of 2
–IN A
+IN A
16 –IN C
15 +IN C
Internal common-mode feedback network
Output balance error −60 dB @ 50 MHz
Differential input and output
B
V
14
V
S–
A
C
S–
Differential-to-differential or single-ended-to-differential
operation
–OUT A
6
13 –OUT C
7
8
9
10
11
12
Adjustable output common-mode voltage
Output pull-down feature for line isolation
Low distortion: 64 dB SFDR @ 10 MHz on 5 V supply,
RL, dm = 200 Ω
Figure 1.
0
Low offset: 4 mV typical output referred on 5 V supply
Low power: 26 mA @ 5 V for three drivers
∆V
= 2V p-p
OUT, dm
OUT, cm
–10 ∆V
/∆V
OUT, dm
Wide supply voltage range: +5 V to 5 V
–20
V
= ±5V
Available in space-saving packaging: 4 mm × 4 mm LFCSP
S
–30
–40
–50
–60
APPLICATIONS
V
= +5V
KVM (keyboard-video-mouse) networking
UTP (unshielded twisted pair) driving
Differential signal multiplexing
S
–70
–80
–90
GENERAL DESCRIPTION
–100
1
10
FREQUENCY (MHz)
100
500
The AD8133 is a major advancement beyond using discrete
op amps for driving differential RGB signals over twisted pair
cable. The AD8133 is a triple, low cost differential or single-
ended input to differential output driver, and each amplifier has
a fixed gain of 2 to compensate for the attenuation of line ter-
mination resistors. The AD8133 is specifically designed for RGB
signals but can be used for any type of analog signals or high speed
data transmission. The AD8133 is capable of driving either Cate-
gory 5 unshielded twisted pair (UTP) cable or differential printed
circuit board transmission lines with minimal signal degradation.
Figure 2. Output Balance vs. Frequency
Manufactured on Analog Devices’ next generation XFCB bipo-
lar process, the AD8133 has a large signal bandwidth of
225 MHz and a slew rate of 1600 V/µs. The AD8133 has an
internal common-mode feedback feature that provides output
amplitude and phase matching that is balanced to −60 dB at
50 MHz, suppressing harmonics and minimizing radiated elec-
tromagnetic interference (EMI).
The outputs of the AD8133 can be set to a low voltage state to
be used with series diodes for line isolation, allowing easy dif-
ferential multiplexing over the same twisted pair cable. The
AD8133 driver can be used in conjunction with the AD8129
and AD8130 differential receivers.
The output common-mode level is easily adjustable by applying
a voltage to the VOCM input pin. The VOCM input can also be used
to transmit signals on the output common-mode voltages.
The AD8133 is available in a 24-lead LFCSP package and can
operate over the temperature range of −40°C to +85°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.