3mm Round
® OptopipeTM
Optical Light Pipe, Bi-Level
515-1061
13.97
[.55]
2.54
4.57
[.18]
Recommended
[.100]
1.91
[.075]
REF
3.05
[.120]
1.52
[.06]
DIFFUSED FRONT
7.62
[.300]
SURFACES;
2 PLCS
MicroLED SMT LEDs
for use with 515-1061
Ø 3.05
[.120] TYP
2 PLCS
5.08
9.14
[.200]
[.36]
1.57
[.062]
2.54
[.100]
2.79
[.11]
2
Ø 1.63
[.064]
MOUNTING
PIN
FRONT
PANEL
5.12
[.200]
2.29
[.090]
2.54
.25
PART NO.
597-3111-5xx
597-3211-5xx
597-3301-5xx
597-3401-5xx
597-7701-5xx
597-7721-5xx
COLOR
AlGaAs Red
Orange
PAGE #
1-30
[.100]
[.010]
THIS VIEW SHOWS TWO 515-1061
LIGHT PIPES MOUNTED
SIDE BY SIDE
5.12
[.200]
7.87
[.310]
1-30
4.50
1.45
4.50
DIRECTION
OF LIGHT
DIRECTION
OF LIGHT
[.177]
TYP
Green
1-30
1.04
[.041]
TYP
[.057]
[.177]
2.69
[.106]
TYP
TYP
3.35
[.132]
Yellow
1-30
3.89
2.54 ±.05
[.100 ±.002]
1.60
[.063]
TYP
[.153]
Red/Green
Yellow/Green
1-31
Ø1.52 ±.05
[.060 ±.002]
TYP, 2 PLCS
3.73
[.147]
4.27
[.168]
[Ø .060 ±.002]
TYP, 2 PLCS
1-31
2.54 ±.05
[.100 ±.002]
NOTE: designed for
post-reflow
4.39
4.39
[.173]
TYP
[.173]
PC board insertion.
FIGURE A
(USING SINGLE COLOR SMT LEDS)
FIGURE B
(USING BI-COLOR SMT LEDS)
RECOMMENDED SOLDER PAD/HOLES LAYOUT
RECOMMENDED SOLDER PAD/HOLES LAYOUT
Dimensions in mm [inches]
Features
• Can be mounted in arrays spaced .200 apart (min.)
• High transmissivity polycarbonate material
• UL94V-0 compliance
LED Data
• ESD protection (circuit isolation from front panel)
• Wide viewing angle
For absolute maximum ratings and other
electrical and optical data on the recommended
LEDs, refer to LED data sheets.
• Arrays reduce insertion costs
• Allows bi-level SMT indicators
Operating/Storage Temperature
• Secures to PCB by press-fit
–30°C to +100°C
Dialight Optopipe Light Pipe Description
This Optopipe™ is a standard design intended as a SMT compatible replacement for our 553 Series Circuit Board
Indicators. The light outputs are spaced vertically .100" from the PCB to the first element, and then 0.200" between the top
and bottom elements. We recommend a minimum of 0.200" between light pipes as a normal mounting pitch. This
Optopipe™ is held in place by 2 press-fit pins along the bottom of the device. The light pipe is not attached to the panel at
any point but can protrude through holes in the panel. The gently arcing emitting end sticks through the plastic or metal
panel. The light source is Dialight's 597 Series Type 1208 LED. The light pipe material is water clear transmissive
polycarbonate rated UL94-V0, and has a 35% oxygen index.
Dialight can provide custom Optopipe™ solutions for your applications.
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
2-43