587B062LPE - 587B302LPE
Only One Name Means ProTek’Tion™
Lꢀꢁ PRꢀfꢂLE 240ꢃ ꢄꢅ PꢀꢁER LꢂnE ꢆuRꢇE ꢆuPPREꢆꢆꢀR
DEꢆꢅRꢂPꢈꢂꢀn
The 587B Low Profile (LPE) Series is designed for European applicaꢀons where no line to ground or neutral to ground
suppression is allowed. These modules employ a three stage technology proven to be the most cost effecꢀve and reli-
able method in protecꢀng sensiꢀve electronic equipment from over voltage transients.
This series is designed to protect AC powered equipment from the 6,000 Volt peak open circuit voltage and 3,000 Amp
short circuit current as defined in ANSI/IEEE C62.41, Category CI.
The 587BxxxLPE Series offers a high degree of protecꢀon against 240 VAC EMI line noise. It is ideal for protecꢀng 800
Volt components because the solid state TVS technology assures that the line-to-neutral voltage will not exceed 800
Volts. While the modules are designed for transient voltage protecꢀon, the advanced circuitry will also aꢁenuate the
amplitude and slow the rate of rise of high frequency noise acꢀng as an EMI filter. The 587BxxxLPE Series includes
common mode protecꢀon, which are effecꢀve in reducing interference from line to equipment and are effecꢀve in
reducing equipment generated noise to meet FCC, VDE and CSA interference requirements.
Lꢀꢁ PRꢀfꢂLE
fEꢄꢈuREꢆ
ꢄPPLꢂꢅꢄꢈꢂꢀnꢆ
• Compaꢀble with IEC 61000-4-5 (Surge): 1kA, 8/20µs, Level 4 (Line-
Gnd) & 333A, Level 4 (Line-Line)
• Meets ANSI/IEEE C62.41 Outdoor Requirements
• Listed to CSA, File LR65240 (Except 587B302LPE)
• Differenꢀal Mode Protecꢀon
• Hard Wired Equipment AC Power Protecꢀon
• Load Side Distribuꢀon Systems
• Secondary Protecꢀon for Light Industrail AC Power
• Low Clamping Voltage
• Nanosecond Response Time
• Long Life and Maintenance Free
• Finger Safe Connecꢀons
MEꢅhꢄnꢂꢅꢄL ꢅhꢄRꢄꢅꢈERꢂꢆꢈꢂꢅꢆ
• Low Profile Plasꢀc Package
• Approximate Weight: 360 grams
• Flammability Raꢀng UL 94V-0
fꢂꢇuRE 1
fꢂꢇuRE 2
ꢈRꢄnꢆꢂEnꢈ ꢃꢀLꢈꢄꢇE ꢈhREꢄꢈ ꢅꢀnDꢂꢈꢂꢀn
ꢈyPꢂꢅꢄL ꢅLꢄMPꢂnꢇ ꢄꢅꢈꢂꢀn ꢀf ꢄ 15ꢄ MꢀDuLE
6
4
8
6
4
2
0
2
0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
t - ꢈime - µs
t - ꢈime - µs
Figures 1 and 2 are photographs of digiꢀzed waveforms showing the typical clamping acꢀon of a 15A module. A 12 Ohm resistor is used to repre-
sent a 10A equipment load. The load is then subjected to the ANSI/IEEE C62.41 Catagory CI test condiꢀons (6000V/3000A). These photographes
contrast the effect on equipment with and without the protector.
www.protekdevices.com
05064.R6 2/11
Page 1