587B051LP - 587B301LP
Only One Name Means ProTek’Tion™
Lꢀꢁ PRꢀfꢂLꢃ 120ꢄ ꢅꢆ PꢀꢁꢃR Lꢂnꢃ ꢇuRꢈꢃ ꢇuPPRꢃꢇꢇꢀR
DꢃꢇꢆRꢂPꢉꢂꢀn
The 587BxxxLP Series of 120 Volt AC Surge Suppressors is designed for use by the OEM, equipment installer and or
maintenance contractor. These modules employ a three stage technology proven to be the most cost effecꢀve and
reliable method in protecꢀng sensiꢀve electronic equipment from over voltage transients. This series is designed to
protect AC powered equipment from the 6,000 volt peak open circuit voltage and 3,000 Amp short circuit current as
defined in ANSI/IEEE C62.41, Category C1.
The 587BxxxLP Series offers a high degree of protecꢀon against 120 VAC EMI line noise. It is ideal for protecꢀng 400
Volt components because the solid state TVS technology assures that the line-to-neutral voltage will not exceed 400
Volts. While the modules are designed for transient voltage protecꢀon, the advanced circuitry will also aꢁenuate the
amplitude and slow the rate of rise of high frequency noise acꢀng as an EMI filter. The 587BxxxLP Series includes dif-
ferenꢀal mode protecꢀon, which is effecꢀve in reducing interference from line to equipment and are effecꢀve in reduc-
ing equipment generated noise to meet FCC, VDE and CSA interference requirements.
Lꢀꢁ PRꢀfꢂLꢃ
fꢃꢅꢉuRꢃꢇ
ꢅPPLꢂꢆꢅꢉꢂꢀnꢇ
• Compaꢀble with IEC 61000-4-5 (Surge): 1kA, 8/20µs, Level 4 (Line-
Gnd) & 333A, Level 4 (Line-Line)
• Meets ANSI/IEEE C62.41 Requirements
• Listed to CSA, File LR65240
• Hard Wired Equipment AC Power Protecꢀon
• Load Side Distribuꢀon Systems
• Secondary Protecꢀon for Light Industrail AC Power
• Differenꢀal and Common Mode Protecꢀon
• Low Clamping Voltage
• Nanosecond Response Time
• Long Life and Maintenance Free
• Finger Safe Connecꢀons
MꢃꢆhꢅnꢂꢆꢅL ꢆhꢅRꢅꢆꢉꢃRꢂꢇꢉꢂꢆꢇ
• Low Profile Plasꢀc Package
• Approximate Weight: 360 grams
• Flammability Raꢀng UL 94V-0
fꢂꢈuRꢃ 1
fꢂꢈuRꢃ 2
ꢉRꢅnꢇꢂꢃnꢉ ꢄꢀLꢉꢅꢈꢃ ꢉhRꢃꢅꢉ ꢆꢀnDꢂꢉꢂꢀn
ꢉyPꢂꢆꢅL ꢆLꢅMPꢂnꢈ ꢅꢆꢉꢂꢀn ꢀf ꢅ 15ꢅ MꢀDuLꢃ
6
4
8
6
4
2
0
2
0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
t - ꢉime - µs
t - ꢉime - µs
Figures 1 and 2 are photographs of digiꢀzed waveforms showing the typical clamping acꢀon of a 15A module. A 12 Ohm resistor is used to repre-
sent a 10A equipment load. The load is then subjected to the ANSI/IEEE C62.41 Catagory CI test condiꢀons (6000V/3000A). These photographes
contrast the effect on equipment with and without the protector.
www.protekdevices.com
05040.R6 9/12
Page 1