Datasheet > 576711

576711

更新时间： 2024-11-21 00:42:11

品牌	Logo	应用领域
泰科 - TE		/
页数	文件大小	规格书
5页	434K
描述
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

576711 数据手册

Instruction Sheet

PIDG* STRATO-THERM*

Terminal Crimping Dies

408-10039

01 JUL 16 Rev D

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low

volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Crimping Dies 576711, 576714, 576715, 576716, 576720, 576723, 576742

Die Holding Screw

Color Code

Stationary Die

Die Holding Screw

Insulation Adjustment Spacers

Moving Die

(Shown in Position 3)

Figure 1

1. INTRODUCTION

The terminal crimping dies listed in Figure 1 are designed to be used with hand tool 69710-1 to crimp PIDG

STRATO-THERM terminals onto wire sizes 24 through 10 AWG. Refer to instruction sheet 408-2095 for

information concerning the hand tool. For other compatible tooling, call the number at the bottom of this page.

Reasons for re-issue of this instruction sheet are provided in Section 7, REVISION SUMMARY.

2. DIE INSTALLATION AND REMOVAL

1. Position the stationary die in the stationary die holder and the moving die in the moving die holder of

the tool. Turn each die holding screw just enough to hold the dies in place. Do not tighten the screws.

2. Position a terminal and wire in the dies as described in steps 1 through 3 of Section 3, then close the

tool handles until the dies bottom.

3. Tighten both the die holding screws while dies are bottomed.

NOTE

Check die alignment and tighten the die holding screws at least twice daily.

4. Continue to close the tool handles until the ratchet control releases. Allow the handles to open, then

remove the terminal.

5. To remove the dies, loosen the die holding screws.

3. CRIMPING

1. Strip the wire to the dimension provided in Figure 2.

2. Place the terminal in the stationary die as shown in Figure 3, then close the tool handles until the

terminal is held firmly in place.

NOTE

These dies will not accommodate a terminal having a tongue width exceeding 11.91 mm [.469 in.].

3. Insert the stripped wire into the terminal insulation barrel until the wire butts against the locator.

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

*Trademark

PRODUCT INFORMATION 1-800-522-6752

1 of 5

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

12 3 4 5

中文翻译

下载PDF

与576711相关器件

型号	品牌	获取价格	描述	数据表
5767116-1	MACOM	获取价格	STEP-Z Interconnection System
5767116-2	MACOM	获取价格	STEP-Z Interconnection System
5767116-3	MACOM	获取价格	STEP-Z Interconnection System
5767116-4	MACOM	获取价格	STEP-Z Interconnection System
5767116-5	MACOM	获取价格	STEP-Z Interconnection System
5767116-6	MACOM	获取价格	STEP-Z Interconnection System
5767116-7	MACOM	获取价格	STEP-Z Interconnection System
5767117-1	MACOM	获取价格	STEP-Z Interconnection System
5767117-2	MACOM	获取价格	STEP-Z Interconnection System
5767117-3	MACOM	获取价格	STEP-Z Interconnection System

与576711相关文章

解析光耦仿真器：升级光耦合器技术的必要性
2024-11-18

25
英伟达新一代Blackwell GPU过热问题致交付延迟
2024-11-18

17
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
2024-11-14

49
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
2024-11-14

46

产品中心

服务支持

精选活动

关于我们

帮助中心

576711

576711 数据手册

与576711相关器件

与576711相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

576711

576711 数据手册

与576711相关器件

与576711相关文章

您还可以找

您在本页遇到什么问题？