Differential PECL Crystal Clock Oscillators PECL Outputs
3HPF5761 Series +3.3V “F” family
MERCURY
Since 1973
3HPF5761 features 0.4 ps typical phase jitter and
low phase noise (-132 dBc at 10 KHz for 155.520 MHz).
Differential PECL Outputs meet the requirements for
SONET, XDSL and other communication protocols.
General Specifications
Product Series
Frequency Range
Output Logic
3HPF5761; “F” family characteristics. Tri-State on pad 1
38 MHz ~ 640 MHz.
Differential PECL 100 K square wave
Commercial “ C ”::
-10°C to +70°C
Industrial “ I ”:
-40°C to +85°C
Stability Code
Frequency Stability
±25 ppm
±50 ppm
A
B
D
E
±100 ppm
Custom ±xx ppm
C
Cxx
F
Ixx
vs Operating Temperature
Range
If custom, use “temperature range code + desired ppm stability” for the stability
code. Example: “C20” (±20 ppm over -10 to +70°C) or “I35”.
vs Supply Voltage Change ±3 ppm max.with ±10% supply voltage change
vs Load Change ±2 ppm max.with ±10% Load change:
Supply Voltage VCC
+3.3 V ± 10 %
Output Voltage HIGH “1”, VOH
Output Voltage LOW “0”, VOL
2.275 V min.; 2.420 V max. Condition: 50 ohms to VDD-2V
1.490 V min..; 1.680 V max. Condition: 50 ohms to VDD-2V
38 MHz≤ fout ≤ 100 MHz: 70 mA max.
100 MHz< fout ≤ 320 MHz: 85 mA max
320 MHz< fout ≤ 640 MHz: 95 mA max
50 ohms into VCC-2V or Thevenin equivalent (terminating resistors required on all
outputs).
Current Consumption
Load
fout < 150 MHz: 0.5 ns typical; 0.7 ns max.
150 MHz ≤ fout ≤ 320 MHz: 0.4 ns. typical; 0.55 ns. max
f320 MHz < fout ≤ 640 MHz: 0.3 ns. typical; 0.45 ns. max
Measured at 20% ↔ 80% of the wave form.
Rise Time (Tr) and
Fall Time (Tf)
Duty Cycle
50% ± 5% max. measured at 50% waveform
3HPF5761: Tri-State is on pad 1. Pad 2 is no connection.
3HPF5762: Tri-State is on pad 2. Pad 1 is no connection.
Differential PECL and complimentary PECL outputs.
No Connection
Both outputs are disabled (high impedance) when pad No. 2 is taken
below 0.45*Vcc referenced to ground (threshold). Oscillator is always
ON. Only buffer stage is disabled.
Disable current: 50 uA max. (at 0.0 V).
Disable time: 10 ns max.
At disabled mode, both outputs are enabled when pad No. 2 is taken
above 0.45*Vcc referenced to ground (threshold).
Enable time: 10ns+one period of the output frequency max.
0.5 ps max. (12 KHz to 20 MHz integrated)
Tri-state
Function on
pad No. 1
Disable
Enable
Phase Jitter (RMS)
Offset
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
10 MHz
SSB Phase
MERCURY
www.mercury-crystal.com
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: sales-tw@mercury-crystal.com
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: sales-us@mercury-crystal.com
MERCURY
Page 1 of 4
Date: April 1, 2008
Rev. 1