5秒后页面跳转
捷配首页

Datasheet > 电阻器 > 温度相关电阻器（NTC / PTC）> 307C1318
307C1318 PDF预览

307C1318

更新时间： 2024-11-20 22:45:11
品牌 Logo 应用领域
威世 - VISHAY 电阻器温度相关电阻器NTC温度相关电阻器PTC过载保护
页数 文件大小 规格书
5页 120K
描述
PTCR Overcurrent Protection

阅读下载

中文翻译

获取价格

307C1318 技术参数

是否无铅： 含铅是否Rohs认证： 不符合
生命周期：Active包装说明：,
Reach Compliance Code：unknownECCN代码：EAR99
HTS代码：8533.40.80.70风险等级：5.87
Is Samacsys：N安装特点：THROUGH HOLE MOUNT
端子数量：2封装形状：DISK PACKAGE
额定（AC）电压（URac）：30 V电阻：1.3 Ω
电阻器类型：PTC THERMISTOR子类别：Non-linear Resistors
表面贴装：NO端子位置：RADIAL
端子形状：WIRE热敏电阻器应用：OVERLOAD PROTECTION
Base Number Matches：1

307C1318 数据手册

 浏览型号307C1318的Datasheet PDF文件第2页浏览型号307C1318的Datasheet PDF文件第3页浏览型号307C1318的Datasheet PDF文件第4页浏览型号307C1318的Datasheet PDF文件第5页 
307C Overcurrent Thermistors  
Vishay Cera-Mite  
PTCR Overcurrent Protection  
FEATURES:  
A NEW DIMENSION  
Sizes For Your Application - Hold currents from 5 mA to 1.5 A are available  
in sizes from 4 to 22mm.  
The Positive Temperature Coefficient  
Resistor’s (PTC thermistor) unique property  
of dramatically increasing its resistance  
above the curie temperature makes it  
an excellent candidate for overcurrent  
protection applications. Overcurrent  
situations in electronic devices occur  
due to voltage fluctuations, changes in  
load impedance, or problems with system  
wiring. PTC thermistors monitor current in  
series connected loads, trip in the event  
of excess current, and reset after the  
overload situation is removed, creating a  
new dimension of flexibility for designers.  
Better Protection, Maintenance Free - PTCRs reset after an overcurrent  
situation. Protection levels may be set lower than possible with fuses, without  
worrying about nuisance trips.  
Resetting, Non Cycling - Functioning as a manual reset device, PTCR  
overcurrent protectors remain latched in the tripped state and automatically  
reset only after voltage has been removed. This prevents continuous cycling,  
and protects against reclosing into a fault condition.  
Simplified Mounting - PTCRs may be mounted directly inside end use  
equipment. Unlike fuses, no bulky fuseholder or access for user replacement  
is required.  
Ceramic Material Selection - Various curie materials are available to tailor  
hold and trip current operating points.  
Repeatable, No Hysteresis - After resetting, ceramic PTCRs return to the  
initial resistance value, providing repeatable, consistent protection levels.  
Unlike polymer type PTCRs, Vishay Cera-Mite devices exhibit no resistance  
hysteresis application problems.  
APPLICATIONS:  
• Telecommunication Products  
• Electronic Power Supplies  
• Automotive Motor Protection  
• Industrial Control Systems  
Telecom Line Balance - In telecom circuits matched pairs are used to  
maintain line balance. Unlike polymer PTCRs, ceramic devices maintain  
balance after resetting.  
APPLICATION DATA  
This relationship is shown in Fig P-2,  
which provides hold current (IH) derating  
estimates for ambient temperatures in  
excess of 25°C. Five curie materials  
illustrate the design flexibility offered by  
ceramic PTCR’s.  
In a typical current limiter application, the PTC device is connected in series  
with a load impedance (Fig P-1). When current (I) flows, internal I2R losses  
attempt to increase the PTCR’s temperature. To maintain the low resistance  
“on” state, stabilization must occur below the switching temperature, where  
the heat generated (I2R) is balanced by heat lost due to radiation and  
conduction.  
Hold current (IH) is the maximum continuous current at which a PTCR can  
be maintained in a low resistance “on” state while operating at rated ambient  
temperature (typ 25°C). To prevent nuisance tripping, choose the rated hold  
current to be greater than the normal current expected.  
Fig P-2  
PTC Thermistor Overcurrent Protectors  
Ambient Temperature Derating of Hold and  
Trip Currents  
Since heat dissipated by the device is proportional to the ambient temperature,  
hold current must be derated for ambients higher than 25°C according to  
the following relationship:  
140%  
70°C Curie Material  
80°C Curie Material  
120%  
90°C Curie Material  
105°C Curie Material  
120°C Curie Material  
100%  
80%  
60%  
40%  
20%  
0%  
Hold Current (IH) = D(TSW - TA)  
RPTC  
Where:  
Fig P-1  
D
= Dissipation Constant  
(varies based on disc  
size, wire type, &  
Typical PTC Current Limiter Application  
PTC  
coating material)  
-10  
0
10 20 30 40 50 60 70 80 90 100 110 120  
Ambient Temperature (°C)  
AC  
or  
DC  
TSW = Switching (Curie)  
Temperature of  
V
LOAD  
PTCR Material  
TA = Ambient Temperature  
R
PTC= Resistance of PTCR  
at 25°C  
Document Number: 23089  
Revision 14-May-02  
www.vishay.com  
11  
ceramite.support@vishay.com  
12345

中文翻译

下载PDF

与307C1318相关器件

型号 品牌 获取价格 描述 数据表
307C1321 VISHAY

获取价格

 		PTCR Overcurrent Protection
307C1323 VISHAY

获取价格

 		PTCR Overcurrent Protection
307C1325 VISHAY

获取价格

 		PTCR Overcurrent Protection
307C1326 VISHAY

获取价格

 		PTCR Overcurrent Protection
307C1329 VISHAY

获取价格

 		PTCR Overcurrent Protection
307C1330 VISHAY

获取价格

 		PTCR Overcurrent Protection
307C1331 VISHAY

获取价格

 		PTCR Overcurrent Protection
307C1333 VISHAY

获取价格

 		PTCR Overcurrent Protection
307C1335 VISHAY

获取价格

 		PTCR Overcurrent Protection
307C1336 VISHAY

获取价格

 		PTCR Overcurrent Protection

与307C1318相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证