HARTING Ha-VIS eCon Switches
2 to 16 Ethernet ports RJ45 and SC/LC (SFP)
Unmanaged Plug & Play Ethernet switches for DIN rail assembly in control
cabinets
Ha-VIS eCon 3000
Full Gigabit Ethernet Basic
Commercial Temp.: 0 °C ... +55 °C / Industrial Temp.: -40 °C ... +70 °C
Energy
Efficient
Ethernet
■ Full gigabit Ethernet, non-blocking switch architecture acc.to IEEE 802.3
■ Support of jumbo frames
■ Variants with industrial temperature range of -40°C ... +70 °C
■ Wide range voltage supply 24/48 VDC
■ Surge protection and reverse polarity protection
■ Minimum energy consumption due to Energy-Efficient Ethernet
■ Optimised DIN rail bracket
Target markets
Machinery &
Robotics
Wind Energy
Solar Energy
Industrial network
infrastructures
Automation technology
Transportation
Shipbuilding
General description
The Ha-VIS eCon 3000 Full Gigabit family of unmanaged Ethernet switches
is equipped with up to 16 gigabit Ethernet ports and allow for cost-efficient
and quick expansion and/or reconstruction of network infrastructures with
high bandwidth requirements. In this, all switches support extra-long
Ethernet frames (jumbo frames). The slender design of the switches enables
an extremely high packing density on the DIN rail. Various combinations of
variants with RJ45, fibre optic cables and SFP ports are available. Automatic
detection of the transmission rate (auto-negotiation) and of the wiring of the
twisted pair data cable (autopolarity and auto-MDI(X)) allow for simple plug
& play. All variants are available with the temperature ranges „Industrial“
and „Commercial“.
Technical characteristics
Switch Features
Ethernet Ports 10BASE-Te / 100BASE-TX EEE / 1000BASE-T EEE
Connection type
Auto-negotiation
Auto-polarity
RJ45
Yes
Yes
Enclosures width
Number of ports
Switching technology
Supported standards
Frame Size
MAC table size
Packet buffer size
Non-blocking
Quality of service
Energy-Efficient Ethernet
PROFINET compatible
EthernetIP compatible
25 mm
2, 5, 6, 7
38 mm
16
Store and Forward
IEEE 802.3
Auto-MDI(X)
Yes
10 kbytes
1 Mbit
8 kBytes
Transfer conditions
Transfer speed
Transfer length
Twisted Pair
8k entries
10 / 100 / 1000 Mbit/s
100 m (twisted pair, Cat 5)
512 kBytes
Yes
Yes
Yes
Yes
Yes
Ethernet Ports 1000BASE-SX / 1000BASE-LX
Type of fibre
Multimode (MM)
Singlemode (SM)
SC Duplex
Connection type
Transfer conditions
Wavelength
Transfer speed
Transfer length
Output power
Input sensitivity
FO
Voltage supply
850 nm
0.55 km
-9.5 dBm ... -4 dBm
≤ -17 dBm
1310 nm
Nominal voltage
24 VDC
48 VDC
1000 Mbit/s
Permissible voltage range
9 VDC ... 60 VDC
18 VDC ... 60 VDC
*
**
10 km
(
see table techn. characteristics)
-9.5 dBm ... -3 dBm
≤ -21 dBm
Surge protection
Reverse polarity proof
Starting current
Yes
Yes
1.60 A
3.20 A
Yes (12 A for <=8 ports)/
(2 A for >8 ports)
SFP ports
Overcurrent protection at input
Transfer standard
Connection type
Transfer conditions
Transfer speed
Depending on used SFP
Max. power consumption @ 24 VDC
Cross-section / Wire gauge
Connection type
2.21 W ... 9.17 W
0.08 mm² ... 2.5 mm² (28 AWG ... 12 AWG)
3-pole, pluggable screwed contact
Depending on used SFP, RJ45 or LC
Depending on used SFP, TP or FO
Depending on used SFP, 100 or 1000 Mbit/s
Depending on used SFP
Pinout
+ / - /
SELV (circuit breaker 10 A)
Supply circuit (acc. to 60950)
Transfer length
HARTING Technology Group
P.O.Box 1473, D-32325 Espelkamp
Wilhelm-Harting-Straße 1, D-32325 Espelkamp, Germany
Note: We reserve the right to make technical changes to the products and to the content of this
document at any time without prior notification. The HARTING Technologiegruppe does not accept
any responsibility for possible errors or incompletions in this document. We reserve all the rights to
this document and the topics and illustrations contained within it. Copying, disclosure to third parties
or use of its content - even partially - is forbidden without the prior written consent of the HARTING
Technologiegruppe.
ICPN-Service@harting.com | Service hotline: +49 5772 47-9479
Fax: +49 5772 47-495 | www.HARTING.com/de/ethernet-switches