Datasheet > 2-21002-4

2-21002-4

更新时间： 2024-09-24 01:08:51

品牌	Logo	应用领域
泰科 - TE		/
页数	文件大小	规格书
5页	315K
描述
This instruction sheet provides application instructions, maintenance, and inspection procedures for PIDG STRATO-THERM

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

2-21002-4 数据手册

Instruction Sheet

PIDG* STRATO-THERM

Terminal Crimping Dies

1976976-1 and 1976977-1

408-10228

21 NOV 13 Rev B

2. Loosen the set screw in the yoke.

3. Insert the shank of the nest into the yoke and

tighten the set screw.

Moving

Die

4. Extend the ram until the set screw is visible.

5. Loosen the set screw in the ram.

6. Insert the shank of the indenter into the ram and

tighten the set screw.

Color-Code

7. Return the ram to the down position.

8. Pivot the latch arm and yoke toward each other

until the locking flange secures the latch arm to the

yoke.

2.2. Die Removal

1. Pivot the latch arm away from the yoke to open

the head.

2. Loosen the set screw in the yoke and remove the

nest.

Stationary

Die

Locator

3. Raise the ram to “full-up” position.

4. Loosen the set screw in the ram and remove the

indenter.

Figure 1

1. INTRODUCTION

2.3. Wire Stripping and Crimping Procedure

A. Wire Stripping

This instruction sheet provides application

instructions, maintenance, and inspection procedures

for PIDG STRATO-THERM Terminal Crimping Dies

1976976-1 and 1976977-1 used in Battery Tool

1901343-[ ]. These dies will crimp

PIDG STRATO-THERM Terminals with a wire size

range of 12-10 AWG.

Strip the wires to the dimensions provided in Figure 2.

NOTE

Refer to Paragraph 2.4 for die insulation crimp

adjustment.

Basic instructions on the use of these dies, die

adjustments, wire preparation, etc. are provided in

Section 2, INSTRUCTIONS.

B. Crimping Procedure

DANGER

Avoid personal injury. When operation the tool, exercise

caution while holding terminals or wire near the crimping

area.

Section 3, MAINTENANCE and INSPECTION

PROCEDURES enables you to establish and maintain

a die certification program.

1. Select the proper terminal for the wire to be

crimped.

The dies are coated with oil to prevent rust and

corrosion. With this oil from the dies, particularly from

the crimping area. Instructions for the Battery Tool

1901343-[ ] are found in Instruction Sheet 408-10070.

2. Place the terminal in the stationary die as shown

in Figure 3.

NOTE

Dimensions in this instruction sheet are in millimeters

[with inches in brackets]. Figures and illustrations are for

reference only and are not drawn to scale.

Dies will not accommodate terminals with tongue widths

exceeding 11.91 mm [.469 in.].

3. Jog the ram by pulsing the trigger until the

moving die retains, but does not deform the

terminal.

2. INSTRUCTIONS

2.1. Die Insertion

4. Insert a stripped wire into the terminal until the

wire butts against the locator.

1. Pivot the latch arm away from the yoke to open

the crimping head.

1 of 5

*Trademark

PRODUCT INFORMATION 1-800-522-6752

For latest revision and Regional Customer Service,

visit our website at www.te.com

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners.

12 3 4 5

中文翻译

下载PDF

与2-21002-4相关器件

型号	品牌	获取价格	描述	数据表
22-100-240	ETC	获取价格	Analog IC
2--21002--5	TE	获取价格	Base Assembly Universal
2210-025	ETC	获取价格	ANALOG ACCELEROMETER MODULE
2-21002-6	TE	获取价格	This instruction sheet provides application instructions, maintenance, and inspection proc
2-21002-7	TE	获取价格	THE REPLACEMENT OCEAN STYLE APPLICATOR HAS THE SAME TERMINATOR/PRESS INTERFACE AS APPLICAT
2-21002-8	TE	获取价格	This instruction sheet provides application instructions, maintenance, and inspection proc
2-21002-9	TE	获取价格	THE REPLACEMENT OCEAN STYLE APPLICATOR HAS THE SAME TERMINATOR/PRESS INTERFACE AS APPLICAT
221002M	LITTELFUSE	获取价格	Axial Lead and Cartridge Fuses - Designed to IEC Standard
221004	LITTELFUSE	获取价格	Axial Lead and Cartridge Fuses - Designed to IEC Standard
221004.	LITTELFUSE	获取价格	Axial Lead and Cartridge Fuses - Designed to IEC Standard

与2-21002-4相关文章

SK海力士量产12层HBM3E，容量高达36GB
2024-09-27

4
意法半导体传感器驱动Sphere，开启沉浸式电影新时代
2024-09-27

6
摩尔斯微电子在美国约书亚树国家公园测试 Wi-Fi HaLow
2024-09-18

78
贸泽上架Tallysman TW5386智能GNSS天线
2024-09-18

68

产品中心

服务支持

精选活动

关于我们

帮助中心

2-21002-4

2-21002-4 数据手册

与2-21002-4相关器件

与2-21002-4相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

2-21002-4

2-21002-4 数据手册

与2-21002-4相关器件

与2-21002-4相关文章

您还可以找

您在本页遇到什么问题？