135D
Vishay
www.vishay.com
Wet Tantalum Capacitors Tantalum-Case with Glass-to-Tantalum
Hermetic Seal for -55 °C to +200 °C Operation
FEATURES
• Axial through-hole terminations: standard tin /
lead (SnPb), 100 ꢀ tin (RoHS-compliant)
available
Available
Available
• Standard and extended ratings
• Model 135D tantalum-case electrolytic
capacitors incorporate the advantages of all
the varieties of electrolytic capacitors and
eliminate most of the disadvantages. These
units have a 3 V reverse voltage capability at
+85 °C and a higher ripple current capability
Available
than any other electrolytic type with similar combinations
of capacitance and case size.
PERFORMANCE CHARACTERISTICS
• Designed for the aerospace applications, this capacitor
was developed under partial sponsorship of the Marshall
Space Flight Center, National Aeronautics and Space
Administration. The capacitors have a high resistance to
damage from shock and vibration. Extended range ratings
and high temperature designs are available.
• Model 135D capacitors are commercial equivalents of
Tansitor style; AQ, AR, HAQ, HAR, Mallory-NACC Style;
TLT, TXT, THT, THX and Military Style CLR79 and CLR81,
designed to meet the performance requirements of
Military Specification MIL-PRF-39006/22/25. Capacitors
to meet MIL-PRF-39006/22/25 should be ordered by part
numbers shown in that specification.
Operating Temperature: -55 °C to +85 °C
(to +200 °C with voltage derating)
Capacitance Tolerance: at 120 Hz, +25 °C
20 ꢀ standard. 10 ꢀ, 5 ꢀ available as special.
DC Leakage Current (DCL Max.): at +25 °C and above:
leakage current shall not exceed the values listed in the
Standard Ratings table.
Life Test: capacitors are capable of withstanding a 2000 h
life test at a temperature of +85 °C or +125 °C at the
applicable rated DC working voltage.
Following life test:
1. DCL, measured at +85 °C rated voltage, shall not be in
excess of the original requirement.
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Note
2. The equivalent series resistance shall not exceed 150 ꢀ
of the initial requirement.
*
This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
Please see the information / tables in this datasheet for details
3. Change in capacitance shall not exceed 10 ꢀ from the
initial measurement.
ORDERING INFORMATION
135D
306
X0
006
C
2
E3
MODEL
CAPACITANCE
CAPACITANCE
TOLERANCE
DC VOLTAGE RATING
AT +85 °C
CASE
CODE
STYLE NUMBER
RoHS-
COMPLIANT
This is expressed
in picofarads. The
first two digits are
the significant
figures. The third
is the number of
zeros to follow.
X0 = 20 ꢀ
X9 = 10 ꢀ
X5 = 5 ꢀ
This is expressed in
volts. To complete the
three-digit block,
zeros precede the
voltage rating.
See
Ratings
and
Case
Codes
table
Standard temperature
(max. +125 °C)
0 = no insulating sleeve
2 = polyester insulation sleeve
3 = high temperature
film insulation
E3 = 100 ꢀ tin
termination
(RoHS-compliant
design)
Blank = SnPb
termination
(standard design)
High temperature
(max. +200 °C)
6 = high temperature
film insulation
8 = no insulating sleeve
Note
•
Packaging: the use of formed plastic trays for packaging these axial lead components is standard. Tape and reel is not available due to the
unit weight.
Revision: 02-Nov-17
Document Number: 40024
1
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000