Datasheet > 125968-1

125968-1

更新时间： 2022-02-26 12:35:15

品牌	Logo	应用领域
泰科 - TE		/
页数	文件大小	规格书
4页	111K
描述
Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY.

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

125968-1 数据手册

Instruction Sheet

Crimping Die Assemblies

90240-2, 90248-2, and 90280-1

408-7563

14 MAR 11 Rev B

Moving

Die

Holding

Screw

Floating

Crimper

PIDG* FASTON*

Terminal

Wire

Barrel

Wire Strip

Length

(See Table)

Assembly

Screw

Saddle

Insulation

Barrel

AMP -TAPETRONIC*

Machine 69875

Die

Holding

Screw

Conductor

Insulation

Stationary

Die

NOTE: Not to Scale

TERMINAL

WIRE

DIE

ASSEMBLY

PART NUMBER

(TAPE MOUNTED)

INSULATION

COLOR

RANGE

(AWG)

STRIP LENGTH

+0.41 [.016]

INSULATION

DIA (Max)

SERIES

NUMBER

60894--2

61048--2

61060--2

90248--2

.110

.250

Clear

22 -- 18

5.56 [.219]

2.54 [.100]

6.35 [.250]

90240--2

90280--1

42844--3

61198--4

Green

Yellow

14 -- 12

12 -- 10

8.74 [.344]

7.14 [.281]

Figure 1

screw. The moving die has a die holding screw and a

saddle with an assembly screw, and it is marked to

indicate the wire range crimped.

1. INTRODUCTION

This instruction sheet covers die assemblies that are

used to crimp PIDG FASTON Terminals. Refer to

Figure 1 for appropriate die assembly and terminal

combinations. The dies and terminals are color coded

to indicate accepted wire range. The dies fit into the

AMP--TAPETRONIC Machine 69875. Refer to

Customer Manual 409--1993.

3. DIE INSTALLATION

Prepare the machine to receive dies according to the

instructions in 409--1993 under “Die Replacement”,

and proceed as follows:

All dimensions on this sheet are in millimeters

NOTE

[with inch equivalents provided in brackets].

Figures and illustrations are for identification only

and are not drawn to scale.

1. Position the moving die into the upper crimping

area of the machine and finger tighten the holding

screw.

Read these instructions carefully and completely

before crimping any terminals.

2. Position the stationary die into the lower

crimping area of the machine and start the holding

screw, but do not tighten it.

Reasons for reissue of this instruction sheet are

provided in Section 7, REVISION SUMMARY.

3. Hand cycle the machine until the dies bottom

against each other. Tighten both holding screws.

2. DESCRIPTION (Figure 1)

Each die assembly consists of a stationary die and a

moving die. The stationary die has a die holding

Re--assemble and adjust the machine, again following

the instructions provided in 409--1993.

E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change.

1 of 4

PRODUCT INFORMATION 1--800--522--6752

For latest revision and Regional Customer Service,

TE logo is a trademark.

visit our website at www.te.com

LOC B

*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.

12 3 4

下载PDF

与125968-1相关器件

型号	品牌	描述	获取价格	数据表
125-96-9	WINCHESTER	PLUG TNC HEX	获取价格
125969-1	TE	Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY.	获取价格
125-9760-FTW	RCD	Fixed Resistor, Wire Wound, 1.5W, 976ohm, 55V, 1% +/-Tol, 20ppm/Cel, Through Hole Mount, A	获取价格
125-97R6-FT	RCD	Fixed Resistor, Wire Wound, 1.5W, 97.6ohm, 55V, 1% +/-Tol, 20ppm/Cel, Through Hole Mount,	获取价格
1259-7SDRSYGW	EVERLIGHT	3.0mm Multi-Color Round Type LED Lamps	获取价格
1259-7SDRSYGW/S530-A3	EVERLIGHT	Dual Color LED, Super Deep Red/super Yellow Green, Diffused White, T-1, 3mm, ROHS COMPLIAN	获取价格

产品中心

服务支持

精选活动

关于我们

帮助中心

125968-1

125968-1 数据手册

与125968-1相关器件

与125968-1相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

125968-1

125968-1 数据手册

与125968-1相关器件

与125968-1相关文章

您还可以找

您在本页遇到什么问题？