Datasheet > 1207-0446-01-P1

1207-0446-01-P1

更新时间： 2024-11-04 12:36:51

品牌	Logo	应用领域
其他 - ETC		电源电路
页数	文件大小	规格书
2页	69K
描述
Power Module Controlled Power Supply

阅读下载

中文翻译

获取价格

如果您发现信息不准确，欢迎纠错

1207-0446-01-P1 数据手册

Power Module Controlled Power Supply

(ST-70)

Operation

The ST 70 requires the use of a Power Module. The Power Module selects the desired performance

level for operation. The ST 70 comes standard with three Power Modules, Performance Levels 6.5, 7,

& 7.5. Additional Power Modules are available in heat levels of 5, 5.5, 6, 8, and 8.5. A heat level of 5

corresponds to a nominal temperature of 500 °F; a heat level of 6.5 corresponds to a temperature of

650 °F, etc. Actual measured temperatures on the surface of the tip may vary due to tip geometry.

If the power is turned on while a Power Module is not installed, or if the Power Module is removed

during operation, the system will turn itself off and the LED indicator light on the front panel will turn

red. To operate the unit, please make sure the set-up procedure has been followed, then follow the

procedure below.

1. Install the desired tip heater cartridge or tip.

2. Install the desired Power Module into the Power Port on the front of the unit.

3. The LED indicator will turn amber while the tip is heating to the desired performance level.

4. Once the tip has reached the desired heat level, the LED indicator will turn green and the

system is ready to use.

Auto-Setback and Auto-Off Features

The ST 70 system comes standard with Auto-Setback and Auto-Off Features. These are pre-

programmed for 30 minute Setback and 30 minute Auto Off, which can be turned off by the switch on

the back of the unit. When Setback mode has been entered, the performance level will be adjusted

to 3.5.

Power Module Controlled LED Operation

The colored LED on the power source front panel indicates Power Receptacle output status.

LED Amber to Green - This condition is evident when the system is first powered up (handpiece

heater cold).

LED Green - Handpiece tip has reached set temperature.

LED Red - Indicates an open sensor. Handpiece, Tip Heater Cartridge or power module has

been removed.

LED Off – System is in auto-off mode or no power is being delivered to the handpiece heater. If

the LED never illuminates, check for a faulty handpiece or tip heater cartridge.

LED in Set back- The LED will be Amber or Green depending on the color when it entered

Setback, or Auto Off.

Replacement Power Modules

Page 15 of 20

中文翻译

下载PDF

型号	品牌	获取价格	描述	数据表
1207-0446-02-P1	ETC	获取价格	Power Module Controlled Power Supply
1207-0446-03-P1	ETC	获取价格	Power Module Controlled Power Supply
1207-0446-04-P1	ETC	获取价格	Power Module Controlled Power Supply
1207-0446-05-P1	ETC	获取价格	Power Module Controlled Power Supply
1207-0446-06-P1	ETC	获取价格	Power Module Controlled Power Supply
1207-0446-07-P1	ETC	获取价格	Power Module Controlled Power Supply
1207-0446-08-P1	ETC	获取价格	Power Module Controlled Power Supply
12071-0035	MOLEX	获取价格	M12 4P FEMALE ATTACHABLE PG7
1-207119-0	MACOM	获取价格	PIN HEADER ASSEMBLY, 4 POSITION METRIMATE
1207202	SICK	获取价格	MULTIPLE LIGHT BEAM SAFETY DEVICES