SAKT 1/LT
SAKT 2/LT
Disconnect Terminals
Slide link disconnect terminals offer a superior
solution for simple current transformer circuits
and measurement transformer test sets using
SAKT 1/LT lateral disconnect terminals, or
SAKT 1/DU feed through terminals and
SAKT 1/QT cross disconnect terminals.
Current transformers must always have a
closed secondary circuit, even when changing
measuring equipment (see schematic below).
Slide Link
Slide Link
Terminal Block Selection Data
Available Options
Version
PA
2 StB test points PA
Back wall closed KrG
0105660000
0269120000
0437920000
0105420000 0445420000
Back wall open KrG
1
k
2
l
3
k
4
l
5
k
6
7
8
9
10
N
4 StB 14 test points ø4.0 KrG 60 V**
1 StB 8.5 test point ø2.0 KrG
1 StB 8.5 test point ø2.3 KrG
2 StB 14 test points ø4 KrG
2 StB 14 test points ø2.3 KrG
0437720000
0106020000
0105920000
0105620000 0330620000
l
L1 L2 L3
L1
L2
Dimensions
Width / Length / Height mm (in.)
for TS 32
for TS 35
8/65/52.5 (.31/2.56/2.07)
8/65/48.5 (.31/2.56/1.91)
12 (.47)
8/82/52.5 (.31/3.23/2.07)
8/82/48.5 (.31/3.23/1.91)
12 (.47)
L3
N
Insulation stripping length
mm (in.)
Technical Data
Rated voltage / rated current / wire size UL
300 V / 25 A / #22...8 AWG*
300 V / 25 A / #26...8 AWG
300 V / 25 A / #22...8 AWG*
300 V / 25 A / #26...8 AWG
CSA
VDE
Stationary Jumpers
2
2
380 VAC / 27 A / 6 mm
380 VAC / 27 A / 6 mm
QL jumpers serve as fixed cross-connections
for the Disconnect Terminals. The QL jumpers
require the use of a fixing screw (BS M) and a
connection sleeve (VH) when attaching the
jumper to the current bar. The WQV jumpers
are provided with a retained jumper screw.
Torque
Nm (lb. in.)
M
1.7 (16)
3.5
1.7 (16)
3.5
Clamping screw
‡
Selected Accessory Data
End Plate (thickness mm)
Type
Part No. Type
0146760000 AP (1.5)
Part No.
PA
AP (1.5)
AP (3.0)
0146760000
0329120000
KrG
0146720000 AP (1.5)
Partition (thickness mm)
PA
KrG
HP
TW (1.5)
TW (3.0)
TW (0.5)
0242960000 TW (1.5)
0242920000 TW (2.5)
0474700000 TW (0.5)
0242960000
0351820000
0474700000
Sliding Jumpers
QS and QVS jumpers are sliding jumpers.
These jumpers are used to temporarily
connect or disconnect adjacent terminal
blocks. When the jumper screws are loose,
the jumper can move to either open or close
the cross connection between blocks.
Tightening the jumper screws holds the
jumper in either the open (disconnected)
or closed (shorted) position.
Small Partition
Jumpers
TSch 2
0353660000 TSch 2
0353660000
QL 2
0194300000 QL 2
0194400000 QL 3
0194500000 QL 4
0338300000 QL 10
0249000000 VH 12
0194300000
0194400000
0194500000
0338300000
0249000000
QL 3
QL 4
QL 10
VH 12
QL fixed
QVS sliding
Connection sleeve
Fixing screw
BS M 3 x 20 Cu 0377100000 BS M 3 x 20 Cu 0377100000
QS 2
0270960000 QS 2
0307300000 QVS 2
0329300000 QVS 3
0307400000 QVS 4
0318000000 VH 19
0334700000 BS 25 bare
0270960000
0307300000
0329300000
0307400000
0318000000
0334700000
QB jumpers work in a similar manner except
that the jumpers remain fixed. An internal
sliding connection link connected to the
current bar either opens or closes the
connection based on whether the link
is in contact with the jumper or not.
QVS 2
QVS 3
QVS 4
VH 19
Final number indicates number of poles. See the Accessories Section
for more information.
Connection sleeve
Fixing screw
BS 25 bare
Switchable Jumper Links
QB 2
QB 3
QB 4
QB 10
0205700000 QB 2
0205800000 QB 3
0205900000 QB 4
0343800000 QB 10
0205700000
0205800000
0205900000
0343800000
SSP disconnect locks snap into the terminal
block. These locks must be removed to
change the position of the sliding link
connection.
QB
Test Plugs
PS 4
0299600000 PS 4
0531760000 SSP 3
0299600000
0531760000
Disconnect Lock
SSP 3
Marking Tags
Print
Consecutive horizontal
Consecutive vertical
DEK 5/6
DEK 5/6
0468660001 DEK 5/6
0468760001 DEK 5/6
0468660001
0468760001
Note: Part numbers are shown
for a single card of pre-printed
tags numbered 1-50.
‡
See Accessories section for additional information.
*For TS 35 #22...8 AWG
132
**With AP 380 V
5秒后页面跳转
全球首块英伟达H200交付 黄仁勋“送货上门”
常用8脚开关电源芯片型号大全
74HC04芯片引脚图及功能、应用电路图讲解
CR6842芯片参数、引脚配置、应用电路图详解
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
